Registration number:
CAD-CAM Workshop Limited
for the Year Ended 31 March 2019
CAD-CAM Workshop Limited
Contents
Company Information |
|
Balance Sheet |
|
Notes to the Financial Statements |
CAD-CAM Workshop Limited
Company Information
Director |
Mr D Brookes |
Company secretary |
Mrs K Brookes |
Registered office |
|
Accountants |
|
Page 1 |
CAD-CAM Workshop Limited
(Registration number: 03177264)
Balance Sheet as at 31 March 2019
Note |
2019 |
2018 |
|||
Fixed assets |
|||||
Tangible assets |
|
|
|||
Current assets |
|||||
Debtors |
|
|
|||
Cash at bank and in hand |
|
|
|||
|
|
||||
Creditors: Amounts falling due within one year |
( |
( |
|||
Net current assets |
|
|
|||
Total assets less current liabilities |
|
|
|||
Creditors: Amounts falling due after more than one year |
- |
( |
|||
Provisions for liabilities |
( |
( |
|||
Net assets |
|
|
|||
Capital and reserves |
|||||
Called up share capital |
|
|
|||
Profit and loss account |
|
|
|||
Total equity |
|
|
For the financial year ending 31 March 2019 the company was entitled to exemption from audit under section 477 of the Companies Act 2006 relating to small companies.
Director's responsibilities:
• |
|
• |
The director acknowledges his responsibilities for complying with the requirements of the Act with respect to accounting records and the preparation of accounts. |
These financial statements have been prepared in accordance with the special provisions relating to companies subject to the small companies regime within Part 15 of the Companies Act 2006.
These financial statements have been delivered in accordance with the provisions applicable to companies subject to the small companies regime and the option not to file the Profit and Loss Account has been taken.
Page 2 |
CAD-CAM Workshop Limited
(Registration number: 03177264)
Balance Sheet as at 31 March 2019
Approved and authorised by the
.........................................
Director
Page 3 |
CAD-CAM Workshop Limited
Notes to the Financial Statements for the Year Ended 31 March 2019
General information |
The company is a private company limited by share capital, incorporated in England and Wales.
The address of its registered office is:
These financial statements were authorised for issue by the
Accounting policies |
Summary of significant accounting policies and key accounting estimates
The principal accounting policies applied in the preparation of these financial statements are set out below. These policies have been consistently applied to all the years presented, unless otherwise stated.
Statement of compliance
These financial statements have been prepared in accordance with Financial Reporting Standard 102 Section 1A - 'The Financial Reporting Standard applicable in the UK and Republic of Ireland' and the Companies Act 2006.
Basis of preparation
These financial statements have been prepared using the historical cost convention except that as disclosed in the accounting policies certain items are shown at fair value.
Revenue recognition
Turnover comprises the fair value of the consideration received or receivable for the sale of goods and provision of services in the ordinary course of the company’s activities. Turnover is shown net of sales/value added tax, returns, rebates and discounts.
Tax
The tax expense for the period comprises current and deferred tax. Tax is recognised in profit or loss, except that a change attributable to an item of income or expense recognised as other comprehensive income is also recognised directly in other comprehensive income.
The current income tax charge is calculated on the basis of tax rates and laws that have been enacted or substantively enacted by the reporting date in the countries where the company operates and generates taxable income.
Deferred tax is recognised in respect of all timing differences between taxable profits and profits reported in the financial statements.
Unrelieved tax losses and other deferred tax assets are recognised when it is probable that they will be recovered against the reversal of deferred tax liabilities or other future taxable profits.
Deferred tax is measured using the tax rates and laws that have been enacted or substantively enacted by the reporting date and that are expected to apply to the reversal of the timing difference.
Page 4 |
CAD-CAM Workshop Limited
Notes to the Financial Statements for the Year Ended 31 March 2019
Tangible assets
Tangible assets are stated in the statement of financial position at cost, less any subsequent accumulated depreciation and subsequent accumulated impairment losses.
Depreciation
Depreciation is charged so as to write off the cost of assets, other than land and properties under construction over their estimated useful lives, as follows:
Asset class |
Depreciation method and rate |
Equipment |
25% reducing balance |
Cash and cash equivalents
Cash and cash equivalents comprise cash on hand and call deposits, and other short-term highly liquid investments that are readily convertible to a known amount of cash and are subject to an insignificant risk of change in value.
Trade debtors
Trade debtors are amounts due from customers for merchandise sold or services performed in the ordinary course of business.
Trade creditors
Trade creditors are obligations to pay for goods or services that have been acquired in the ordinary course of business from suppliers.
Borrowings
Interest-bearing borrowings are initially recorded at fair value, net of transaction costs. Interest-bearing borrowings are subsequently carried at amortised cost, with the difference between the proceeds, net of transaction costs, and the amount due on redemption being recognised as a charge to the Profit and Loss Account over the period of the relevant borrowing.
Leases
Leases are classified as finance leases whenever the terms of the lease transfer substantially all the risks and rewards of ownership to the lessee.
Share capital
Ordinary shares are classified as equity. Equity instruments are measured at the fair value of the cash or other resources received or receivable, net of the direct costs of issuing the equity instruments.
Dividends
Dividend distribution to the company’s shareholders is recognised as a liability in the financial statements in the reporting period in which the dividends are declared.
Staff numbers |
The average number of persons employed by the company (including the director) during the year, was
Page 5 |
CAD-CAM Workshop Limited
Notes to the Financial Statements for the Year Ended 31 March 2019
Tangible assets |
Furniture, fittings and equipment |
Total |
|
Cost or valuation |
||
At 1 April 2018 |
|
|
Additions |
|
|
At 31 March 2019 |
|
|
Depreciation |
||
At 1 April 2018 |
|
|
Charge for the year |
|
|
At 31 March 2019 |
|
|
Carrying amount |
||
At 31 March 2019 |
|
|
At 31 March 2018 |
|
|
Debtors |
2019 |
2018 |
|
Trade debtors |
|
|
Prepayments |
|
|
|
|
Creditors |
Creditors: amounts falling due within one year
Note |
2019 |
2018 |
|
Due within one year |
|||
Bank loans and overdrafts |
|
|
|
Accruals and deferred income |
|
|
|
Other creditors |
|
|
|
|
|
Creditors: amounts falling due after more than one year
Page 6 |
CAD-CAM Workshop Limited
Notes to the Financial Statements for the Year Ended 31 March 2019
Note |
2019 |
2018 |
|
Due after one year |
|||
Loans and borrowings |
- |
|
Loans and borrowings |
2019 |
2018 |
|
Non-current loans and borrowings |
||
Finance lease liabilities |
- |
|
2019 |
2018 |
|
Current loans and borrowings |
||
Finance lease liabilities |
|
|
Page 7 |